Home > HARDWARE > CONSTRUCTION HARDWARE
Choose a sub category:
JOBSITE HARDWARE POLYETHYLENE FILM FOUNDATION HARDWARE
BUILDING HARDWARE LUMBER / MOLDING/TRIM CEILINGS
FLOORING /ACCESSORIES GUTTER VENTILATION PRODUCTS
JOIST HANGERS & CONNECTORS DECK & PATIO CONSTRUCTION DOORS
WINDOWS
Sort By:
1 2 3
Frost King SP1/12 Construction Insulation Ad Tech T3438CK Mixing Nozzle Kit Blueskin HE201WB929 Flash Membrane
Creates an insulating barrier that retains heat or cold, seals out weather and damps vibration. Can be used around water heaters, oil burners, heating and air conditioner ducts; prevents heat loss and sweating on pipes, auto hoods and trunks. Nozzle kit for Ultrabond epoxy 22 oz. system.  Hi-Flow nozzles reduce waste while increasing flow. 15 inch length snaps off to 10 inches if required.  3/8 diameter at tip.  Built in mixing nut allows for fast and easy attachment to cartridge. A self-adhering membrane consisting of an SBS rubberized asphalt compound which is integrally laminated to a blue-engineered film. Excellent adhesion to prepared substrates of concrete, concrete block, primed steel, aluminum mill finish, anodized aluminum, galvanized metal, gypsum board and plywood; impermeable to air, moisture vapor and water; easy to install peel and stick application, no flame required; thickness controlled at point of manufacture; membrane is self-sealing when penetrated with self-tapping screws or nails. Thickness: 25 mils.
Blue Skin BH200WB4559 Window and Door Flashing Blueskin HE572110 Adhesive Prep Spray Blueskin HE201WB968 Flash Membrane
Self-adhering membrane consisting of an SBS rubberized asphalt compound which is integrally laminated to a blue engineered film. The membrane is specifically designed to be self-adhered to a prepared substrate. SBS modified membrane can be applied in temperatures as low as 10 F. Blue polypropylene film top surface and siliconized release film bottom surface. Excellent adhesion to prepared substrates of concrete, concrete block, primed steel, aluminum mill finish, anodized aluminum, galvanized metal, gypsum board, and plywood. Impermeable to air, moisture vapor, and water. Peel and stick application; no flame required. Factory controlled thickness. .9mm thickness. Self-sealing when punctured. Rubber based spray adhesive designed to enhance the adhesion of "Blueskin" membranes. Quick setting. Aggressive tack provides adhesion of membrane. Suitable for application at normal and low temperatures. Clear amber color. -10 degrees to 104 degrees Fahrenheit application temperature. 3-minute drying time for initial set. 20-minute drying time for set through. Spray can application eliminates the need for brushes or rollers. 30 to 50 sq. ft./can coverage depending on porosity and texture of surface. 15 Oz. Can. A self-adhering membrane consisting of an SBS rubberized asphalt compound which is integrally laminated to a blue-engineered film. Excellent adhesion to prepared substrates of concrete, concrete block, primed steel, aluminum mill finish, anodized aluminum, galvanized metal, gypsum board and plywood; impermeable to air, moisture vapor and water; easy to install peel and stick application, no flame required; thickness controlled at point of manufacture; membrane is self-sealing when penetrated with self-tapping screws or nails. Thickness: 25 mils.
Vestal AD459 Ash Dump INSUL R13K 15IN X 32FT ROLL   Vestal ST-88 Cleanout Door
Cooled ashes are swept into ash dump to be cleaned later. USA made. Kraft faced mini rolls - "Greenguard" certified LEED eligible. Allows debris to be swept and removed that has collected in the chimney. Domestic.
Ultra Bond 1 A9-1 Anchoring Adhesive Reflectix 2222-16-25 7-Layer Reflective Staple Tab Insulation Miraclebond 1350 A9-MB1350HN Anchoring Adhesive
Use for anchoring and doweling. Long working time with a quick cure time. Moisture insensitive, can be used in underwater environments, concrete, hollow block, brick, clay and stone. Ideal for vertical, horizontal, and screen applications, seismic anchoring and bracing, surface crack repair. Ultra high-strength epoxy mixes through a static mixing tube and can also be resealed which means that any remaining material can be saved for later use. Cartridge w/nozzle. Easy installation ? scissors and staple gun are all you need.  3/4" staple tab designed for 16" OC Joists. All season performance.  Great for insulating radiant heating systems.  5/16? thick, multi layer, double bubble reflective insulation .  Reflects 94% of radiant heat.  Class 1, Class A fire rating.  Any seams should be sealed with TVM Metalized Tape for maximum effectiveness. Two component (1:1 ratio), 100-percent solids, high aspect ceramic blend, solvent-free, non-sag, high strength, high modulus, moisture insensitive epoxy system. Ideal for use as a bonding agent for almost any material, including metal, concrete, brick, wood, stone, block and other substrates. Can also be used for repairing holes, spalls, cracks in concrete, repairing rotted wood, installing and repairing anchor bolts or hand rails. LIMITATIONS: Minimum substrate and ambient temperature 40 degrees F (4.44 degrees C),  Cartridge with two nozzles; medium duty caulking tool required.
Marshall JP16 Adjustable Extend-O-Post Jackpost Blueskin HE201WB954 Flash Membrane TVM 2220-48-10 Double Bubble Construction Insulation
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. A self-adhering membrane consisting of an SBS rubberized asphalt compound which is integrally laminated to a blue-engineered film. Excellent adhesion to prepared substrates of concrete, concrete block, primed steel, aluminum mill finish, anodized aluminum, galvanized metal, gypsum board and plywood; impermeable to air, moisture vapor and water; easy to install peel and stick application, no flame required; thickness controlled at point of manufacture; membrane is self-sealing when penetrated with self-tapping screws or nails. Thickness: 25 mils. Safe to use; non-toxic; easy to install.  Does not require special protective clothing.  Lowers air conditioning/heating costs.  5/16? thick, multi layer, double bubble reflective insulation in rolls of various widths and lengths.  Reflects 94% of radiant heat. Class 1, Class A fire rating.  Seams should be sealed with TVM Metalized Tape for maximum effectiveness.
Protecto Seal 45 805204SW Exposable Waterproofing Membrane Ultra Bond 1300 A22-1300N Anchoring Adhesive Blue Skin BH200WB4590 Window and Door Flashing
Exposable membrane is quick and easy to use. Made with styrene-butadeine-styrene (SBS) modified rubberized asphalt pressure-sensitive adhesive. Durable, puncture and abrasion resistant. A cross laminated polyethylene film is laminated to an aluminum foil for ultraviolet and weather resistance. Shrink Wrapped. Two  component (1:1 ratio), 100 percent solids, high modulus, structural epoxy gel. It is a solvent free, low odor high strength, moisture insensitive, non-sag epoxy system. The resin and hardener are uniformly dispensed from a dual cartridge system and mixed simultaneously through a mixing nozzle or available in bulk. Long working time with a full cure in 24 hours. Moisture insensitive, may be used in damp environments, concrete, hollow block, brick, clay and stone. Ideal for vertical, horizontal, and screen applications. Structural bonding of concrete to concrete. Meets ASTM C881-14: Type I, II, IV and V, Grade 3, Class B and C. Cartridges with Nozzle. Self-adhering membrane consisting of an SBS rubberized asphalt compound which is integrally laminated to a blue engineered film. The membrane is specifically designed to be self-adhered to a prepared substrate. SBS modified membrane can be applied in temperatures as low as 10 F. Blue polypropylene film top surface and siliconized release film bottom surface. Excellent adhesion to prepared substrates of concrete, concrete block, primed steel, aluminum mill finish, anodized aluminum, galvanized metal, gypsum board, and plywood. Impermeable to air, moisture vapor, and water. Peel and stick application; no flame required. Factory controlled thickness. .9mm thickness. Self-sealing when punctured.
Ultra Bond 1 A22-1 Anchoring Adhesive INSUL R19K 6.25H X 15L X 94W  INSUL R19K 15IN X 39.16FT ROLL
Use for anchoring and doweling. Long working time with a quick cure time. Moisture insensitive, can be used in underwater environments, concrete, hollow block, brick, clay and stone. Ideal for vertical, horizontal, and screen applications, seismic anchoring and bracing, surface crack repair. Ultra high-strength epoxy mixes through a static mixing tube and can also be resealed which means that any remaining material can be saved for later use. Cartridge w/nozzle. Kraft Faced Pro Cut Batts - "Greenguard" certified LEED eligible. Kraft faced rolls - "Greenguard" certified LEED eligible.
Marshall JP36 Adjustable Extend-O-Post Jackpost Blueskin HE201WB976 Flash Membrane Permapro 04100PRO House Wrap
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. A self-adhering membrane consisting of an SBS rubberized asphalt compound which is integrally laminated to a blue-engineered film. Excellent adhesion to prepared substrates of concrete, concrete block, primed steel, aluminum mill finish, anodized aluminum, galvanized metal, gypsum board and plywood; impermeable to air, moisture vapor and water; easy to install peel and stick application, no flame required; thickness controlled at point of manufacture; membrane is self-sealing when penetrated with self-tapping screws or nails. Thickness: 25 mils. Stops winds from robbing homes of their energy and insulation values. Reduces the air exchange that occurs in homes as air moves through the wall cavities. Tiny micro perforations also allow the release of water vapor to help prevent any moisture condensation. Water resistant air infiltration barrier is lightweight and easy to install, yet is strong and durable which reduces jobsite waste. 5.0 Mil. Thickness.
Protecto Wrap 8250055 Energy Sill Seal Blue Skin BH200WB4335 Window and Door Flashing TVM 75055 Sill Seal
Combination of 3/8" closed cell polyethylene foam with an aggressive self adhesive waterproofing membrane. Conforms and seals off the voids and irregularities between the top of the foundations and sill plate. Stops heating and air condition loss at the foundation to sill plate interface. Eliminates air, moisture and insect/rodent infiltration beneath the sill plate; energy saving, mildew and water resistant. Self-adhering membrane consisting of an SBS rubberized asphalt compound which is integrally laminated to a blue engineered film. The membrane is specifically designed to be self-adhered to a prepared substrate. SBS modified membrane can be applied in temperatures as low as 10 F. Blue polypropylene film top surface and siliconized release film bottom surface. Excellent adhesion to prepared substrates of concrete, concrete block, primed steel, aluminum mill finish, anodized aluminum, galvanized metal, gypsum board, and plywood. Impermeable to air, moisture vapor, and water. Peel and stick application; no flame required. Factory controlled thickness. .9mm thickness. Self-sealing when punctured. Designed to fill the air gaps between the sill plate and the foundation wall, reducing air infiltration. It's durable, moisture resistant characteristics prevent water and insect intrusion. Made of high grade polyethylene. Yellow color. Prevents rotting of the sill plate and will not deteriorate.
Marshall JP55 Adjustable Extend-O-Post Jackpost TVM 75035 Sill Seal INSUL R11K 15IN X 70.5FT ROLL
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. Designed to fill the air gaps between the sill plate and the foundation wall, reducing air infiltration. It's durable, moisture resistant characteristics prevent water and insect intrusion. Made of high grade polyethylene. Yellow color. Prevents rotting of the sill plate and will not deteriorate. Kraft faced rolls - "Greenguard" certified LEED eligible.
   
 
1 2 3